document no. u15207ej1v0um00 (1st edition) date published april 2001 n cp(k) printed in japan user?s manual IE-78K0S-NS-A in-circuit emulator target devices 78k/0s series ? 2001
user?s manual u15207ej1v0um 2 [memo]
user?s manual u15207ej1v0um 3 v851 and v850 family are trademarks of nec corporation. windows is either a registered trademark or trademark of microsoft corporation in the united states and/or other countries. pc/at is a trademark of international business machines corporation. m8e 00. 4 the information in this document is current as of april, 2001. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec's data sheets or data books, etc., for the most up-to-date specifications of nec semiconductor products. not all products and/or types are available in every country. please check with an nec sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without prior written consent of nec. nec assumes no responsibility for any errors that may appear in this document. nec does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec semiconductor products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. nec assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec endeavours to enhance the quality, reliability and safety of nec semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. nec semiconductor products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. the recommended applications of a semiconductor product depend on its quality grade, as indicated below. customers must check the quality grade of each semiconductor product before using it in a particular application. "standard": computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "special": transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "specific": aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. the quality grade of nec semiconductor products is "standard" unless otherwise expressly specified in nec's data sheets or data books, etc. if customers wish to use nec semiconductor products in applications not intended by nec, they must contact an nec sales representative in advance to determine nec's willingness to support a given application. (note) (1) "nec" as used in this statement means nec corporation and also includes its majority-owned subsidiaries. (2) "nec semiconductor products" means any semiconductor product developed or manufactured by or for nec (as defined above). ? ? ? ? ? ?
user ? s manual u15207ej1v0um 4 regional information some information contained in this document may vary from country to country. before using any nec product in your application, piease contact the nec office in your country to obtain a list of authorized representatives and distributors. they will verify: ? device availability ? ordering information ? product release schedule ? availability of related technical literature ? development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, ac supply voltages, and so forth) ? network requirements in addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. nec electronics inc. (u.s.) santa clara, california tel: 408-588-6000 800-366-9782 fax: 408-588-6130 800-729-9288 nec electronics (germany) gmbh duesseldorf, germany tel: 0211-65 03 02 fax: 0211-65 03 490 nec electronics (uk) ltd. milton keynes, uk tel: 01908-691-133 fax: 01908-670-290 nec electronics italiana s.r.l. milano, italy tel: 02-66 75 41 fax: 02-66 75 42 99 nec electronics (germany) gmbh benelux office eindhoven, the netherlands tel: 040-2445845 fax: 040-2444580 nec electronics (france) s.a. velizy-villacoublay, france tel: 01-3067-5800 fax: 01-3067-5899 nec electronics (france) s.a. madrid office madrid, spain tel: 091-504-2787 fax: 091-504-2860 nec electronics (germany) gmbh scandinavia office taeby, sweden tel: 08-63 80 820 fax: 08-63 80 388 nec electronics hong kong ltd. hong kong tel: 2886-9318 fax: 2886-9022/9044 nec electronics hong kong ltd. seoul branch seoul, korea tel: 02-528-0303 fax: 02-528-4411 nec electronics singapore pte. ltd. novena square, singapore tel: 253-8311 fax: 250-3583 nec electronics taiwan ltd. taipei, taiwan tel: 02-2719-2377 fax: 02-2719-5951 nec do brasil s.a. electron devices division guarulhos-sp, brasil tel: 11-6462-6810 fax: 11-6462-6829 j01.2
user?s manual u15207ej1v0um 5 introduction product overview the IE-78K0S-NS-A is used in combination with an emulation board (ie-789 -ns-em1) to debug products of the 78k/0s series of 8-bit single-chip microcontrollers. readers this manual is intended for engineers who perform debugging of systems, using products of the 78k/0s series of 8-bit single-chip microcontrollers with the IE-78K0S-NS-A and an emulation board (ie-789 -ns- em1). purpose this manual is intended to give users an understanding of the debugging functions that are available by using the IE-78K0S-NS-A and the emulation board (ie-789 -ns-em1) together. organization when using the IE-78K0S-NS-A, please refer to the manual (this manual) that comes with the ie-78k0s-ns- a as well as the manual that comes with the emulation board (ie-789 -ns-em1). ? basic specifications ? function outline ? system configuration ? target interface differences ? external interface function how to read this manual to understand the overall functions of the IE-78K0S-NS-A read this manual in the order of the contents . to understand the basic specifications refer to chapter 1 general and chapter 2 part names . for how to connect the ie-789 -ns-em1 and make settings to debug 78k/0s series products refer to chapter 3 installation . IE-78K0S-NS-A user?s manual (this manual) ie-789 -ns-em1 user?s manual
user?s manual u15207ej1v0um 6 terminology the meanings of the terms used in this manual are described in the table below. terms meaning emulation devices refers to the generic name for the devices in the emulator that perform emulation of the target device. this includes the emulation cpu. emulation cpu refers to the cpu that executes the user?s program in the emulator. target device refers to the device to be emulated. target system refers to the system to be debugged. this includes the target program and the hardware created by the user. in the narrow sense, it means hardware only. conventions data significance: higher digits on the left and lower digits on the right note : footnote for item marked with note in the text caution : information requiring particular attention remark : supplementary information
user?s manual u15207ej1v0um 7 contents chapter 1 general.......................................................................................................... .............. 10 1.1 system configuration ........................................................................................................ ...................... 10 1.2 hardware configuration ...................................................................................................... .................... 12 1.3 basic specifications ........................................................................................................ ........................ 13 1.4 contents in carton .......................................................................................................... ......................... 15 chapter 2 part names ...................................................................................................... .......... 17 2.1 parts of main unit.......................................................................................................... ........................... 17 2.2 board name .................................................................................................................. ............................ 19 2.3 external sense probe names................................................................................................. ................. 20 chapter 3 installation..................................................................................................... .......... 21 3.1 connection .................................................................................................................. ............................. 21 3.2 external trigger functions.................................................................................................. .................... 28 3.3 external sense .............................................................................................................. ........................... 28 3.4 jumper settings (on main board)............................................................................................. .............. 29 appendix a interface board (ie-70000-pci-if(-a)) for desktop pc........................... 30 a.1 introduction ................................................................................................................ .............................. 30 a.2 installation ................................................................................................................ ................................ 31 appendix b pc card interface (ie-70000-cd-if-a) .............................................................. 32 b.1 introduction ................................................................................................................ .............................. 32 b.2 installation ................................................................................................................ ................................ 33 appendix c interface board (ie-70000-98-if-c) for pc-9800 series (except for nx series).......................................................................................... 34 c.1 introduction ................................................................................................................ .............................. 34 c.2 installation ................................................................................................................ ................................ 35 appendix d interface board (ie-70000-pc-if-c) for ibm pc/at and compatibles .................................................................................................... 37 d.1 introduction ................................................................................................................ .............................. 37 d.2 installation ................................................................................................................ ................................ 38
user?s manual u15207ej1v0um 8 list of figures figure number title page 1-1 IE-78K0S-NS-A system configuration .......................................................................................... ............. 11 1-2 basic hardware configuration of IE-78K0S-NS-A ............................................................................... ....... 12 1-3 contents in carton.......................................................................................................... ............................ 15 1-4 contents in accessory bag................................................................................................... ...................... 16 2-1 main board (IE-78K0S-NS-A) .................................................................................................. ................... 19 3-1 connecting emulation board <1> (when ie-789 -ns-em1 uses single-board configuration)............. 22 3-2 connecting emulation board <2> (when ie-789 -ns-em1 uses 2-board configuration)..................... 23 3-3 connecting external sense probe............................................................................................. ................. 24 3-4 connecting emulation probe (when ie-789 -ns-em1 uses single-board configuration).................... 25 3-5 connecting emulation probe (when ie-789 -ns-em1 uses 2-board configuration)............................ 26 3-6 connecting ac adapter ....................................................................................................... ....................... 27 3-7 connecting dedicated bus interface cable.................................................................................... ............ 27 3-8 default settings of jp1 and jp3 ............................................................................................. .................... 29 3-9 jumper position on main board............................................................................................... ................... 29 a-1 mounting of pci board and connector boards .................................................................................. ........ 31 c-1 int jp, wait jp settings.................................................................................................... ....................... 36 d-1 int jp, wait jp settings.................................................................................................... ....................... 39
user?s manual u15207ej1v0um 9 list of tables table number title page 1-1 list of functions (max. specifications) ..................................................................................... ................. 13 2-1 bit configuration when connecting external sense probe to extcn1 .................................................... 20 2-2 bit configuration when connecting external sense probe to extcn2 .................................................... 20 3-1 electrical characteristics .................................................................................................. .......................... 28 3-2 electrical specifications of external sense ................................................................................. ............... 28 c-1 sw1 and sw2 settings when setting i/o address to 01d h ................................................................... 35 d-1 sw1 and sw2 settings when setting i/o address to 020 h .................................................................... 38
user?s manual u15207ej1v0um 10 chapter 1 general the IE-78K0S-NS-A is a development tool for effectively debugging hardware and software using a 78k/0s series 8-bit single-chip microcontroller. this chapter describes the system configuration and basic specifications of the IE-78K0S-NS-A. 1.1 system configuration figure 1-1 shows the system configuration of the IE-78K0S-NS-A.
chapter 1 general user?s manual u15207ej1v0um 11 figure 1-1. IE-78K0S-NS-A system configuration conversion socket/conversion adapter axs note 2 nps- note 2 ev- - note 3 tg - note 4 (sold separately) integrated debugger id78k0s-ns (sold separately) device file s df789 (sold separately) control software host machine pc-9800 series or ibm pc/at tm and compatibles IE-78K0S-NS-A (this product) interface cable (ns interface cable) in-circuit emulator fc cable pc card interface interface cable ns card cable mc card cable note 1 pc card interface ie-70000-cd-if-a (sold separately) ac adapter ie-70000-mc-ps-b (sold separately) emulation board ie-789 -ns-em1 (sold separately) emulation probe np- note 2 (sold separately) interface board ie-70000-98-if-c (sold separately) interface board ie-70000-pc-if-c (sold separately) interface board ie-70000-pci-if(-a) (sold separately) or notes 1. this cable is used for the v850 family tm . it cannot be used for the IE-78K0S-NS-A. 2. the np- , axs , and nps- are products of naito densei machida mfg. co., ltd. (tel + 81-45-475-4191). contact an nec distributor when purchasing. 3. the ev- - is a product of nec. 4. the tg - is a product of tokyo eletech corporation. inquiries: daimaru kougyo, ltd. tokyo electronic division (tel: + 81-3-3820-7112) osaka electronic division (tel: + 81-6-6244-6672)
chapter 1 general user ? s manual u15207ej1v0um 12 1.2 hardware configuration the IE-78K0S-NS-A consists of the following hardware units (such as cabinet and boards). ? cabinet ? 78k0s main board ? 78k0s emulation board ? ns interface cable figure 1-2. basic hardware configuration of IE-78K0S-NS-A host machine interface board (sold separately) interface card (sold separately) dedicated bus interface 78k0s main board IE-78K0S-NS-A emulation probe (sold separately) emulation board ie-789 -ns-em1 (sold separately) ie-789 -ns-em1 external sense probe
chapter 1 general user ? s manual u15207ej1v0um 13 1.3 basic specifications table 1-1. list of functions (max. specifications) (1/2) parameter description supervisor v851 tm (operating frequency: 33.0 mh z ) target device 78k0s series ( pd789 ) system clock depends on the specifications of the emulation board (sold separately) (20 mhz max.) external pulse input clock supply internal mounted on an emulation board (sold separately) emulation memory capacity 64 kb internal rom 256 bytes (64 kb max.) internal high-speed ram 8 bytes (1 kb max.) mapping unit internal low-speed ram 64 bytes (16 kb max.) emulation function ? real-time execution ? break execution ? step execution real-time internal ram monitor ? space: all the internal ram area ? timing: data access event detection ? program execution detection: 10 (brs1 to brs10) ? bus event detection: 12 (bra1 to bra12) event integration ? external trigger detection ? external trigger output (open drain output: 1) ? path counter ? trace qualify condition ? delay condition ? trigger condition break factor ? event break ? manual break ? command break ? fail-safe break ? external exclusive event input (1 + 16) trace factor ? all traces ? qualify trace ? section trace trace capacity 128 bits 8 kb real-time trace trace content address, data, status, and external sense trace: 16 pins (alternately function as external exclusive event inputs)
chapter 1 general user ? s manual u15207ej1v0um 14 table 1-1. list of functions (max. specifications) (2/2) parameter description execution time measurement up to 4 mins. 28 sec., resolution: 62.5 ns time measurement between events ? can be changed from 160 ns to 20.56 s resolution ? maximum measurement time when 160 ns resolution is set: 11 minutes when 20.56 s resolution is set: 24 hours coverage between 64 kb (read, write, fetch) dmm 22 events target interface emulation probe (sold separately) provided for each target device shape host interface dedicated bus interface low-voltage support based on the guaranteed operating range of the target device host machine pc-9800 series, or ibm pc/at and compatibles power supply dc 5 v dimensions w235 d195 h39 (mm)
chapter 1 general user ? s manual u15207ej1v0um 15 1.4 contents in carton the IE-78K0S-NS-A carton contains the main unit, cables, an accessory bag, and a guarantee card. make sure that the accessory bag contains a packing list, this user ? s manual, spacers, and screws. in the case of missing or damaged items, please contact an nec sales representative or nec distributor. please make sure to fill out and return the guarantee card that comes with the main unit. figure 1-3. contents in carton <2> ns interface cable <3> fg cable <1> IE-78K0S-NS-A <7> guarantee card <6> accessory bag <4> external sense probe <5> external sense clip <1> IE-78K0S-NS-A main unit 1 <2> ns interface cable 1 <3> fg cable 1 <4> external sense probes 2 <5> external sense clips 20 (10 per case 2) <6> accessory bag 1 <7> guarantee card 1
chapter 1 general user ? s manual u15207ej1v0um 16 check that the accessory bag contains the following items (refer to figure 1-4 contents in accessory bag ). packing list 1 user ? s manual (this manual) 1 screws 4 figure 1-4. contents in accessory bag (a) packing list (b) user's manual (c) screws
user?s manual u15207ej1v0um 17 chapter 2 part names this chapter introduces the parts of the IE-78K0S-NS-A main unit. the packing box contains the IE-78K0S-NS-A main unit. if there are any missing or damaged items, please contact an nec sales representative. please make sure to fill out and return the guarantee document that comes with the main unit. 2.1 parts of main unit (1) probe end t v c c extcn2 extcn1 target system power supply led probe interface (2) top view power in circuit emulator power supply led
chapter 2 part names user ? s manual u15207ej1v0um 18 (3) interface fg off on reset host-i/f dc in - + reset switch (reset) dedicated bus interface connector (host-i/f) power switch (off/on)
chapter 2 part names user ? s manual u15207ej1v0um 19 2.2 board name the IE-78K0S-NS-A contains this board. ? main board (IE-78K0S-NS-A): 1 check that you have the correct board. to access the inside of the unit, remove the four screws from the sides of the main unit and open the lid. figure 2-1. main board (IE-78K0S-NS-A) jp1 jp3 cn7 p3 p2 cn8 j4 j1 cn1 sw1 jk1 cn5 cn6 p1 extcn1 extcn2
chapter 2 part names user ? s manual u15207ej1v0um 20 2.3 external sense probe names the IE-78K0S-NS-A includes external sense probes and external sense clips. (1) external sense probes: 2 color of cable black n.c. gray purple blue green yellow orange red brown connector no. 10 9 8 7 6 5 4 3 2 1 the names of the external sense probes when they are connected to extcn1 and extcn2 are as follows. table 2-1. bit configuration when connecting external sense probe to extcn1 connector no. 1 2 3 45678910 external sense ext1 ext2 ext3 ext4 ext5 ext6 ext7 ext8 n.c. gnd color of cable brown red orange yellow green blue purple gray n.c. black table 2-2. bit configuration when connecting external sense probe to extcn2 connector no. 1 2 3 45678910 external sense ext9 ext10 ext11 ext12 ext13 ext14 ext15 ext16 n.c. gnd color of cable brown red orange yellow green blue purple gray n.c. black remark n.c.: no connection (2) external sense clips: 20 (16 for external sense probe, 2 for gnd, and 2 spares) made by sunhayato corporation (2 sets of 10)
user?s manual u15207ej1v0um 21 chapter 3 installation this chapter describes how to connect the cables to the IE-78K0S-NS-A and the mode settings. 3.1 connection connect the following seven products which are sold separately. for the interface adapter, be sure to select a product supported by the host machine. refer to figure 1-1 system configuration of IE-78K0S-NS-A in chapter 1 general for the system configuration of the IE-78K0S-NS-A. ? ie-70000-98-if-c: interface board (use cable that comes with IE-78K0S-NS-A) ? ie-70000-pc-if-c: interface board (use cable that comes with IE-78K0S-NS-A) ? ie-70000-pci-if(-a): interface board (use cable that comes with IE-78K0S-NS-A) ? ie-70000-cd-if: pc card interface (ns card cable and mc card cable are included) ? ie-70000-mc-ps-b: ac adapter ? ie-789 -ns-em1: emulation board ? np- : emulation probe caution connecting and removing cables or components from the target system and changing the settings of switches, etc. should be carried out after turning off the power of the IE-78K0S-NS-A main unit and the target system.
chapter 3 installation user?s manual u15207ej1v0um 22 (1) connecting emulation board (ie-789 -ns-em1: for single-board configuration) the ie-789 -ns-em1 is sold separately. figure 3-1. connecting emulation board <1> (when ie-789 -ns-em1 uses single-board configuration) <1> remove the screws from the sides of the main unit, and then remove the top cover. <3> replace the spacers (metal) of the main board, as indicated in the diagram below, with the spacers (plastic) attached to the ie- 78k0s-ns-a. <5> when using a probe, connect the probe. <2> remove the first plate from the bottom by removing the screws. <4> connect the ie-789 -em1 and fasten the two screws to the emulation board. <6> replace the top cover and fasten the four screws on the sides. here emulation board refer to (4) for the probe connection method. refer to (3) for the external sense probe connection method.
chapter 3 installation user ? s manual u15207ej1v0um 23 (2) connecting emulation board (ie-789 -ns-em1: probe board + i/o board) (2-board configuration) the ie-789 -ns-em1 is sold separately. figure 3-2. connecting emulation board <2> (when ie-789 -ns-em1 uses 2-board configuration) <1> remove the screws from the sides of the main unit, and then remove the top cover. <3> connect the i/o board and affix the attached spacers to the ie-789 -ns-em1 at four points on the board. <5> when using a probe, connect the probe. <2> remove the first and second plates from the bottom by removing the screws. <4> connect the probe board on the i/o board and fasten the four screws. <6> replace the top cover and fasten the four screws on the sides. here i/o board attached spacer attached spacer fix fix probe board i/o board refer to (5) for the probe connection method. refer to (3) for the external sense probe connection method. ie-789 -ns-em1 (probe board) ie-789 -ns-em1 (i/o board)
chapter 3 installation user ? s manual u15207ej1v0um 24 (3) connecting external sense probe figure 3-3. connecting external sense probe extcn1 extcn2 110 110 ground line (black) ground line (black) external sense probe (included 2) main board (IE-78K0S-NS-A)
chapter 3 installation user ? s manual u15207ej1v0um 25 (4) connecting emulation probe (np- ) (when ie-789 -ns-em1 uses single-board configuration) the np- is sold separately. figure 3-4. connecting emulation probe (when ie-789 -ns-em1 uses single-board configuration) emulation probe (np- ) ie-789 -ns-em1 main board (IE-78K0S-NS-A) caution the emulation probe (np- ) mounting location varies depending on the model of the i/o emulation board (ie-789 -ns-em1) in use. for details, refer to the ie-789 -ns-em1 user?s manual.
chapter 3 installation user ? s manual u15207ej1v0um 26 (5) connecting emulation probe (np- ) (when ie-789 -ns-em1 uses 2-board configuration) the np- is sold separately. figure 3-5. connecting emulation probe (when ie-789 -ns-em1 uses 2-board configuration) emulation probe (np- ) ie-789 -ns-em1 (probe board) main board (IE-78K0S-NS-A) ie-789 -ns-em1 (i/o board) caution the emulation probe (np- ) mounting location varies depending on the model of the i/o emulation board (ie-789 -ns-em1) in use. for details, refer to the ie-789 -ns-em1 user?s manual.
chapter 3 installation user ? s manual u15207ej1v0um 27 (6) connecting ac adapter (ie-70000-mc-ps-b) the ie-70000-mc-ps-b is sold separately. <1> insert the ac adapter plug into the dc in socket of the IE-78K0S-NS-A. figure 3-6. connecting ac adapter (7) connecting interface cable the ie-70000-98-if-c, ie-70000-pc-if-c, ie-70000-pci-if(-a), and ie-70000-cd-if-a are sold separately. <1> insert the interface cable into the bus interface connector on the IE-78K0S-NS-A main unit. figure 3-7. connecting dedicated bus interface cable caution the type of interface cable varies depending on the interface board and pc card interface. ? ? ? ? when using an interface board (ie-70000-98-if-c, ie-70000-pc-if-c, or ie-70000-pci-if(-a)) connect the ns interface cable that comes with the IE-78K0S-NS-A. ? ? ? ? when using a pc card interface (ie-70000-cd-if-a) connect the ns card cable that comes with the ie-70000-cd-if-a. fg off on reset host-i/f dc in - + reset switch (reset) dedicated bus interface connector (host-i/f) power switch (off/on) fg off on reset host-i/f dc in - + reset switch (reset) dedicated bus interface connector (host-i/f) power switch (off/on)
chapter 3 installation user ? s manual u15207ej1v0um 28 3.2 external trigger functions (1) extout at the occurrence of a break event, the extout pin on the emulation board (ie-789 -ns-em1) outputs a low level for 1.3 s. caution because the output is open drain, connect a pull-up resistor in the target system. (2) extin the extin pin on the emulation board (ie-789 -ns-em1) can be used to input an event signal. enter high- level pulse signals for two or more cpu clocks. caution for the electrical characteristics, refer to table 3-1. table 3-1. electrical characteristics parameter min. [v] max. [v] input voltage, high target voltage 0.7 target voltage input voltage, low 0 target voltage 0.3 3.3 external sense data of up to 16 bits can be input to the IE-78K0S-NS-A from the target system via an external sense probe. also, when using an external sense break, input a level of at least 2 cpu clocks. table 3-2. electrical specifications of external sense parameter min. [v] max. [v] input voltage, high target voltage note 0.7 target voltage note input voltage, low 0 target voltage note 0.3 note 2.0 v when the target voltage is less than 2.0 v.
chapter 3 installation user ? s manual u15207ej1v0um 29 3.4 jumper settings (on main board) (1) default settings of jumper figure 3-8. default settings of jp1 and jp3 3 2 jp1 1 jp3 jp1: 1 and 2 are shorted (set at shipment) jp3: shorted (do not change) caution the make the jumper settings, follow the procedure in the user?s manual of the emulation board (ie-789 -ns-em1). figure 3-9. jumper position on main board jp1 jp3
user?s manual u15207ej1v0um 30 appendix a interface board (ie-70000-pci-if(-a)) for desktop pc this chapter describes the setting method when connecting the IE-78K0S-NS-A. for details, refer to the ie-70000-pci-if(-a) user?s manual (to be prepared). a.1 introduction the ie-70000-pci-if(-a) is an interface board for an ie series product that is installed in the pci bus slot of a pc incorporating windows tm 95/98 or windows nt4.0/2000. first of all, check that you have the following items. ? interface board (ie-70000-pci-if(-a)) for desktop pc 1 ? 8-bit connector board (connected to ie-70000-pci-if(-a)) 1 ? 32-bit connector board 1 ? user?s manual 1 ? dll-disk 1 ? ie-pc driver disk 1 ? guarantee card 1 applicable models the ie-70000-pci-if(-a) is designed for devices incorporating windows 95/98 or windows nt4.0/2000 and a premounted pci bus slot. hardware resources used ? i/o address .........0000h to ffffh ? interrupts ............unused ? memory...............uses 80h bytes current consumption 300 ma (max. when using +5 v) cautions 1. do not place heavy objects on or apply pressure to the board. 2. do not drop the board or subject it to excessive vibration or shock. 3. when removing a cable, do not pull it by the cord. 4. do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. avoid subjecting the board to extreme changes in temperature or humidity. 6. do not spill drinks or other liquids onto the board or its accessories. 7. do not connect a cable for a different product to the connector.
appendix a interface board (ie-70000-98-if-c) for pc-9800 series user?s manual u15207ej1v0um 31 a.2 installation (1) board settings there are no jumpers or dip switches on the ie-70000-pci-if(-a). (2) 8-bit connector board mounting an 8-bit connector board is premounted at shipment. remark when a 32-bit board is mounted, place it on the 8-bit connector board using the combination connector (refer to figure a-1 ) and fasten them together with screws. caution the 32-bit connector board is included for future function expansion. figure a-1. mounting of pci board and connector boards ch1 ch0 pci board 32-bit connector board combination connector combination connector combination connector 8-bit connector board (3) installation in pc make sure that the pc is turned off, then install the interface board in the pci bus slot following the instructions in the pc ? s manual. at installation, fasten the pci board to the pc with screws. (4) ie-pc driver installation refer to the supplied ie-pc driver disk readme_e.txt for ie-pc driver installation. (5) connecting with IE-78K0S-NS-A using the supplied cable, connect the IE-78K0S-NS-A to the ch0 side. caution connection with the IE-78K0S-NS-A is possible on the ch0 side only.
user?s manual u15207ej1v0um 32 appendix b pc card interface (ie-70000-cd-if-a) this chapter describes the setting method when connecting the IE-78K0S-NS-A. for details, refer to the ie-70000-cd-if-a user?s manual (to be prepared). b.1 introduction the pc card interface (ie-70000-cd-if-a) is an interface card for an ie product that is installed in the pcmcia2.1/jeida standard ver. 4.2-compliant pc card slot of a pc incorporating windows 95/98 or windows nt4.0/2000. first of all, check that you have the following items. ? pc card interface (ie-70000-cd-if-a) 1 ? mc-a cable 1 ? ns-a cable 1 ? user?s manual 1 ? dll-disk 1 ? ie-pc driver disk 1 ? guarantee card 1 applicable models the ie-70000-cd-if-a is designed for devices incorporating windows 95/98 or windows nt4.0/2000 and a premounted pc card slot compliant with pcmcia2.1/jeida standard ver.4.2. hardware resources used ? i/o address .........20h bytes starting from 220h, 260h, 2e0h, 320h, or 3e0h as a base address ? interrupts ............unused ? memory...............unused current consumption 300 ma (max. when using +5 v) cautions 1. do not place heavy objects on or apply pressure to the board. 2. do not drop the board or subject it to excessive vibration or shock. 3. when removing a cable, do not pull it by the cord. 4. do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. avoid subjecting the board to extreme changes in temperature or humidity. 6. do not spill drinks or other liquids onto the board or its accessories. 7. do not connect a cable for a different product to the connector.
appendix b pc card interface (ie-70000-cd-if-a) user?s manual u15207ej1v0um 33 b.2 installation (1) installation in pc for windows 95/98/2000, insert the pcmcia card in the card slot when the power supply of the pc is turned on. for windows nt4.0, insert the card in the slot when the power supply is turned off. be careful to insert the card in the correct direction. (2) ie-pc driver installation refer to the supplied ie-pc driver disk readme_e.txt for pcmcia driver installation. caution this interface card cannot be connected to the ie-78 -r. actually, installation ends completely by selecting ?ie-78 -r? displayed in the ie-pc driver disk installation menu. in this case, however, the installation is invalid. (3) connection with the IE-78K0S-NS-A using the ns card cable, connect the ie-70000-cd-if-a to the IE-78K0S-NS-A. caution be sure to use the ns card cable when connecting to the IE-78K0S-NS-A. if mc card cable is used, the ie-70000-cd-if-a may be damaged.
user?s manual u15207ej1v0um 34 appendix c interface board (ie-70000-98-if-c) for pc-9800 series (except for nx series) this chapter describes the setting method when connecting the IE-78K0S-NS-A. for details, refer to the ie-70000-98-if-c user?s manual (to be prepared). c.1 introduction the ie-70000-98-if-c is an interface board for the pc-9800 series (except for nx series) that is installed in the c bus slot of a pc-9800 series (except for nx series) machine. caution the pc98-nx series is treated as an ibm pc/at compatible machine. refer to appendix a interface board (ie-70000-pci-if(-a)) for desktop pc. first of all, check that you have the following items. ? interface board (ie-70000-98-if-c) for pc-9800 series 1 ? user?s manual 1 ? dll-disk 1 ? ie-pc driver disk 1 ? guarantee card 1 applicable models this product is designed for devices incorporating windows 95/98 or windows nt4.0/2000 with an on-chip pc- 9800 series c bus. hardware resources used ? i/o addresses .............. 16 bytes in a 256-byte boundary (00d h, 01d h,...ffd h) ? interrupts and others ... unused current consumption 500 ma (max. when using + 5 v) cautions 1. do not place heavy objects on or apply pressure to the board. 2. do not drop the board or subject it to excessive vibration or shock. 3. when removing a cable, do not pull it by the cord. 4. do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. avoid subjecting the board to extreme changes in temperature or humidity. 6. do not spill drinks or other liquids onto the board or its accessories. 7. do not connect a cable for a different product to the connector.
appendix c interface board (ie-70000-98-if-c) for pc-9800 series (except for nx series) user?s manual u15207ej1v0um 35 c.2 installation (1) i/o address settings sw1 and sw2 are the switches selecting the c bus i/o addresses. sw1 numbers 1 to 8 correspond to c bus addresses a4 to a11, and sw2 numbers 1 to 4 correspond to c bus addresses a12 to a15. in the IE-78K0S-NS-A, the addresses should be set in the 16 bytes between 00d h and ffd h. the switch takes the value ?0? when on and ?1? when off. the addresses used for setup must be values that are not used in the pc system or for other boards. in addition, since these values are used during software installation, make a note of them for future reference. setting examples of i/o address, sw1 and sw2 are shown below. table c-1. sw1 and sw2 settings when setting i/o address to 01d h sw1 number12345678 address a4 a5 a6 a7 a8 a9 a10 a11 on 0 000 off 1 1 1 1 sw2 number12345678 address a12 a13 a14 a15 off off on off on 0 000 0 off 1 1 1 caution set sw2 number 7 to on and sw2 numbers 5, 6, and 8 to off.
appendix c interface board (ie-70000-98-if-c) for pc-9800 series (except for nx series) user?s manual u15207ej1v0um 36 (2) jumper settings the int jp and wait jp are c bus interrupt and wait selection jumpers. in the IE-78K0S-NS-A, set int jp to no use, and wait jp to 1 and 2 shorted. figure c-1. int jp, wait jp settings 12 wait jp 3 : shorted 12 int jp shorted no use ir3 ir5 ir6 ir9 ir11 ir12 ir13 (3) installation in pc make sure that the pc is turned off, then install the interface board in the c bus slot following the instructions in the pc ? s manual. at installation, fasten the interface board to the pc with screws. (4) ie-pc driver installation refer to the supplied ie-pc driver disk readme_e. txt for ie-pc driver installation. (5) connecting with IE-78K0S-NS-A using the supplied cable, connect the IE-78K0S-NS-A to ch0. caution connection with the IE-78K0S-NS-A is possible to ch0 only. for connection with other models, refer to their respective manuals.
user?s manual u15207ej1v0um 37 appendix d interface board (ie-70000-pc-if-c) for ibm pc/at and compatibles this chapter describes the setting method when connecting the IE-78K0S-NS-A. for details, refer to the ie-70000-pc-if-c user?s manual (to be prepared). d.1 introduction the ie-70000-pc-if-c is an interface board for ibm pc/at and compatibles and is installed in the isa bus slot of ibm pc/at and compatibles. first of all, check that you have the following items. ? interface board (ie-70000-pc-if-c) for ibm pc/at 1 ? user?s manual 1 ? dll-disk 1 ? ie-pc driver disk 1 ? guarantee card 1 applicable models the ie-70000-pc-if-c is designed for ibm pc/at and compatibles incorporating windows 95/98 or windows nt4.0/2000 with an on-chip isa bus. hardware resources ? i/o address.................. 16 bytes in any 16-byte boundary (020 h to 03f h) ? interrupts and others ... unused current consumption 500 ma (max. when using + 5 v) cautions 1. do not place heavy objects on or apply pressure to the board. 2. do not drop the board or subject it to excessive vibration or shock. 3. when removing a cable, do not pull it by the cord. 4. do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. avoid subjecting the board to extreme changes in temperature or humidity. 6. do not spill drinks or other liquids onto the board or its accessories. 7. do not connect a cable for a different product to the connector.
appendix d interface board (ie-70000-pc-if-c) for ibm pc/at and compatibles user?s manual u15207ej1v0um 38 d.2 installation (1) i/o address settings sw1 and sw2 are the switches selecting the isa bus i/o addresses. sw1 numbers 1 to 8 correspond to isa bus addresses a4 to a11, and sw2 numbers 1 to 4 correspond to isa bus addresses a12 to a15. in the IE-78K0S-NS-A, the addresses should be set between 020 h and 03f h. the switch takes the value ?0? when on and ?1? when off. the addresses used for setup must be values that are not used in the pc system or for other boards. in addition, since these values are used during software installation, make a note of them for future reference. setting examples of i/o address, sw1 and sw2 are shown below. table d-1. sw1 and sw2 settings when setting i/o address to 020 h sw1 number12345678 address a4a5a6a7a8a9a10a11 on 0 0000 00 off 1 sw2 number12345678 address a12 a13 a14 a15 off off on off on 0 000 0 off 1 1 1 caution set sw2 number 7 to on and sw2 numbers 5, 6, and 8 to off.
appendix d interface board (ie-70000-pc-if-c) for ibm pc/at and compatibles user?s manual u15207ej1v0um 39 (2) jumper settings the int jp and wait jp are isa bus interrupt and wait selection jumpers. in the IE-78K0S-NS-A, set int jp to no use, and wait jp to 1 and 2 shorted. figure d-1. int jp, wait jp settings 12 wait jp 3 : shorted 12 int jp no use shorted irq2 irq3 irq4 irq5 irq6 irq7 (3) installation in pc make sure that the pc is turned off, then install the interface board in the isa bus slot following the instructions in the pc ? s manual. at installation, fasten the interface board to the pc with screws. (4) ie-pc driver installation refer to the supplied ie-pc driver disk readme_e. txt for ie-pc driver installation. (5) connecting with IE-78K0S-NS-A using the supplied cable, connect the IE-78K0S-NS-A to ch0. caution connection with the IE-78K0S-NS-A is possible to ch0 only. for connection with other models, refer to their respective manuals.
user ? s manual u15207ej1v0um 40 [memo]
user ? s manual u15207ej1v0um 41 [memo]
user ? s manual u15207ej1v0um 42 [memo]
although nec has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. despite all the care and precautions we've taken, you may encounter problems in the documentation. please complete this form whenever you'd like to report errors or suggest improvements to us. hong kong, philippines, oceania nec electronics hong kong ltd. fax: +852-2886-9022/9044 korea nec electronics hong kong ltd. seoul branch fax: +82-2-528-4411 taiwan nec electronics taiwan ltd. fax: +886-2-2719-5951 address north america nec electronics inc. corporate communications dept. fax: +1-800-729-9288 +1-408-588-6130 europe nec electronics (europe) gmbh technical documentation dept. fax: +49-211-6503-274 south america nec do brasil s.a. fax: +55-11-6462-6829 asian nations except philippines nec electronics singapore pte. ltd. fax: +65-250-3583 japan nec semiconductor technical hotline fax: +81- 44-435-9608 i would like to report the following error/make the following suggestion: document title: document number: page number: thank you for your kind support. if possible, please fax the referenced page or drawing. excellent good acceptable poor document rating clarity technical accuracy organization cs 01.2 name company from: tel. fax facsimile message
|
